Everything You Ever Wanted to Know About
Power Play Solenoid and Lamp Assignments

The following table lists each driver transistor, the coil it drives,
the pre-driver IC associated with it along with the pin numbers of the base and collector (respectively),
and the decoder IC BINARY input signals (ABCD) and output pin number.

TIP-102
Transistor
Coil CA3081
Pre-Driver IC
74L154
Decoder*
Q1 Chime "10" U1, 16, 1 0001/2
Q2 Down Post U1, 3, 2 0000/1
Q3 Knocker U1, 6, 4 0101/6
Q4 Outhole Kicker U1, 8, 7 0110/7
Q5 Chime "100" U1, 13, 14 0010/3
Q6 Chime "1000" U1, 11, 12 0011/4
Q7 Extra Chime U1, 10, 9 0100/5
Q8 Saucer Kicker U3, 16, 1 0111/8
Q9 Bottom Pop Bumper U3, 3, 2 1010/11
Q10 Left Slingshot U3, 8, 7 1011/13
Q11 Right Slingshot U3, 6, 4 1101/15
Q12 Left Drop Target Reset U3, 10, 9 1100/14
Q13 Left Pop Bumper U3, 11, 12 1000/9
Q14 Right Pop Bumper U3, 13, 14 1001/10
Q15 Flipper Enable Relay U4, 3, 2 n/a
Q16 Right Drop Target Reset U4, 8, 7 1110/16
Q17 Up Post U4, 10, 9 n/a
Q18 Not Used U4, 11, 12 n/a
Q19 Coin Lockout U4, 13, 14 n/a

*NOTE*
"n/a" Decoder info indicates these drivers get their signals as continuous
solenoids directly from the MPU at A4J4-5, 6, 7, and 8 and not the Decoder IC


This table lists all the 2N5060 SCRs on the Lamp Driver module, the name of the lamp it drives,
the decoder IC associated with the SCR along with the BINARY input signals (AD0, AD1, AD2, AD3) and output pin,
and the name of the 2K Ohm resistor (red/black/red) connected to the decoder output.

2N5060
SCR
Lamp MC14514
Decoder
2K Ohm
Resistor
Q4 Saucer 15K U1, 0111/4 R7
Q5 Number of Players "1" U1, 1101/13 R3
Q6 Player Up "1" U1, 1110/16 R2
Q7 Not Used U1, 1011/19 R1
Q11 Saucer 3K U1, 0110/5 R8
Q12 Bonus 5K U1, 0001/9 R12
Q13 Bonus 9K U1, 0010/10 R13
Q14 Bonus 1K U1, 0000/11 R14
Q18 Number of Players "2" U2, 1101/13 R15
Q19 Player Up "2" U2, 1110/16 R11
Q20 Not Used U3, 0111/4 R10
Q21 Not Used U2, 1011/19 R9
Q25 Not Used U2, 0111/4 R22
Q26 Saucer 6K U2, 0110/5 R23
Q27 Bonus 6K U2, 0001/9 R27
Q28 Bonus 10K U2, 0010/10 R28
Q29 Bonus 2K U2, 0000/11 R29
Q30 Number of Players "3" U3, 1101/13 R30
    
2N5060
SCR
Lamp MC14514
Decoder
2K Ohm
Resistor
Q31 Player UP "3" U3, 1110/16 R26
Q32 Saucer 9K U3, 0110/5 R25
Q36 Bonus 3K U3, 0000/11 R45
Q37 Not Used U3, 0101/6 R38
Q38 Bonus 7K U3, 0001/9 R41
Q39 Right Outlane Special U3, 1011/9 R24
Q43 Number of Players "4" U4, 1101/13 R44
Q44 Bonus 20K U3, 0010/10 R43
Q45 Player Up "4" U4, 1110/16 R42
Q46 Bottom Pop Bumper U4, 1001/17 R40
Q50 Bonus 8K U4, 0001/9 R55
Q51 Not Used U4, 0010/10 R56
Q52 Credit Index U4, 1010/20 R37
Q53 Left Lane Special U4, 1011/19 R39
Q57 Bonus 4K U4, 0000/11 R57
Q58 Not Used U4, 0111/4 R50
Q59 Top U4, 0110/5 R53
Q60 Not Used U4, 0101/6 R54


This table lists all the MCR-106 SCRs on the Lamp Driver module, the name of the lamp it drives,
the MC14514 decoder IC associated with the SCR along with the BINARY input signals (AD0, AD1, AD2, AD3) and output pin,
the CD4050 driver IC associated with the SCR along with the input and output pins,
and the name of the 2K Ohm resistor (red/black/red) connected to the decoder output.

MCR-106
SCR
Lamp MC14514
Decoder
CD4050
Driver*
2K Ohm
Resistor
Q1 Not Used U1, 1000/18 U5, 14/15 R6
Q2 Not Used U1, 1001/17 U5, 11/12 R5
Q3 Shoot Again (playfield) U1, 1010/20 U5, 9/10 R4
Q8 Right Alley Rollover (1x) U1, 0011/8 U5, 3/2 R16
Q9 Potential 2X Bonus U1, 0100/7 U5, 5/4 R17
Q10 Potential Special U1, 0101/6 U5, 7/6 R18
Q15 High Score to Date U2, 1100/14 U6, 14/15 R19
Q16 Ball in Play U1, 1100/14 U6, 11/12 R20
Q17 Post Up (2x) U2, 1001/17 U6, 9/10 R21
Q22 Not Used U2, 0101/6 U6, 3/2 R31
Q23 Match U2, 1010/20 U6, 5/4 R32
Q24 5X Bonus Multiplier U2, 1000/18 U6, 7/6 R33
    
MCR-106
SCR
Lamp MC14514
Decoder
CD4050
Driver*
2K Ohm
Resistor
Q33 Game Over U3, 1100/14 U7, 14/15 R34
Q34 Potential 3X Bonus U2, 0100/7 U7, 9/10 R35
Q35 Right Alley Rollovers (2x) U2, 0011/8 U7, 11/12 R36
Q40 Same Player Shoots Again U3, 1001/17 U7, 3/2 R46
Q41 Left & Right Pop Bumpers U3, 1001/17 U7, 7/6 R48
Q42 3X Bonus U3, 1000/18 U7, 5/4 R47
Q47 Tilt U4, 1100/14 U8, 14/15 R49
Q48 Potential 5X Bonus U3, 0100/7 U8, 9/10 R51
Q49 Left Alley Rollover (1x) U3, 0011/8 U8, 11/12 R52
Q54 Left Alley Rollovers (2x) U4, 0011/8 U8, 3/2 R58
Q55 Potential Extra Ball U4, 0100/7 U8, 5/4 R59
Q56 2X Bonus U4, 1000/18 U8, 7/6 R60

*NOTE*
The AS-2518-23 Lamp Driver Module does not use the CD4050 hex driver chips
so ignore that column if that's the style of lamp driver you have.


NOTES
I got all this information from the schematics and pretty much copied it verbatim.
If you notice any mistakes (I'm only human), please let me know and I'll fix it up.
If you need to know which solenoid driver transistor goes to which solenoid driver board connector, Click Here.
If you need to know which lamp SCR goes to which lamp driver board connector, Click Here.



[Steve's Page] [Pinball] [Bally] [Power Play] [Bally Solenoid/Lamp Drivers]



Created 9/12/02 - Last Modified 1/24/09 - Steve Kulpa Mail Icon Nolensville, TN
Remove the NO_S*P*A*M_ to reply

All content posted on this page, unless otherwise noted, is the exclusive property of Steve Kulpa
and may not be borrowed, copied, downloaded, reproduced, or pilfered in any way with out prior permission