Everything You Ever Wanted to Know About
Mata Hari Solenoid and Lamp Assignments

The following table lists each driver transistor, the coil it drives,
the pre-driver IC associated with it along with the pin numbers of the base and collector (respectively),
and the decoder IC input signals (ABCD) and output pin number.

TIP-102
Transistor
Coil CA3081
Pre-Driver IC
74L154
Decoder*
Q1 Chime 10 U1, 16, 1 0001/2
Q2 Saucer Kickout U1, 3, 2 0000/1
Q3 Knocker U1, 6, 4 0101/6
Q4 Outhole Kicker U1, 8, 7 0110/7
Q5 Chime 100 U1, 13, 14 0010/3
Q6 Chime 1000 U1, 11, 12 0011/4
Q7 Extra Chime U1, 10, 9 0100/5
Q8 Left Bottom Pop Bumper U3, 16, 1 0111/8
Q9 Right Bottom Pop Bumper U3, 3, 2 1010/11
Q10 Left Slingshot U3, 8, 7 1011/13
Q11 Right Slingshot U3, 6, 4 1101/15
Q12 Left Drop Target Reset U3, 10, 9 1100/14
Q13 Left Top Pop Bumper U3, 11, 12 1000/9
Q14 Right Top Pop Bumper U3, 13, 14 1001/10
Q15 Flipper Enable Relay U4, 3, 2 n/a
Q16 Right Drop Target Reset U4, 8, 7 1110/16
Q17 Not Used U4, 10, 9 n/a
Q18 Not Used U4, 11, 12 n/a
Q19 Coin Lockout U4, 13, 14 n/a

*NOTE*
"n/a" Decoder info indicates these drivers get their signals as continuous
solenoids directly from the MPU at A4J4-5, 6, 7, and 8 and not the Decoder IC.


This table lists all the 2N5060 SCRs on the Lamp Driver module, the name of the lamp it drives,
the decoder IC associated with the SCR along with the input signals (AD0, AD1, AD2, AD3) and output pin,
and the name of the 2K Ohm resistor (red/black/red) connected to the decoder output.

2N5060
SCR
Lamp MC14514
Decoder
2K Ohm
Resistor
Q4 Not Used U1, 0111/4 R7
Q5 Number of Players 1 U1, 1101/13 R3
Q6 Player Up 1 U1, 1110/16 R2
Q7 Not Used U1, 1011/19 R1
Q11 "AB" Value 5K U1, 0110/5 R8
Q12 Bonus 5K U1, 0001/9 R12
Q13 Bonus 9K U1, 0010/10 R13
Q14 Bonus 1K U1, 0000/11 R14
Q18 Number of Players 2 U2, 1101/13 R15
Q19 Player Up 2 U2, 1110/16 R11
Q20 Right Outlane 50K U3, 0111/4 R10
Q21 5X Multiplier U2, 1011/19 R9
Q25 Not Used U2, 0111/4 R22
Q26 "AB" Value X-Ball U2, 0110/5 R23
Q27 Bonus 6K U2, 0001/9 R27
Q28 Bonus 10K U2, 0010/10 R28
Q29 Bonus 2K U2, 0000/11 R29
Q30 Number of Players 3 U3, 1101/13 R30
    
2N5060
SCR
Lamp MC14514
Decoder
2K Ohm
Resistor
Q31 Player Up 3 U3, 1110/16 R26
Q32 "AB" Value Special U3, 0110/5 R25
Q36 Bonus 3K U3, 0000/11 R45
Q37 "AB" Value 3K U3, 0101/6 R38
Q38 Bonus 7K U3, 0001/9 R41
Q39 3X Multiplier U3, 1011/9 R24
Q43 Number of Players 4 U4, 1101/13 R44
Q44 Bonus 20K U3, 0010/10 R43
Q45 Player Up 4 U4, 1110/16 R42
Q46 2X Potential U4, 1001/17 R40
Q50 Bonus 8K U4, 0001/9 R55
Q51 Drop Target Special U4, 0010/10 R56
Q52 Credit Indicator U4, 1010/20 R37
Q53 2X Multiplier U4, 1011/19 R39
Q57 Bonus 4K U4, 0000/11 R57
Q58 Left Outlane 50K U4, 0111/4 R50
Q59 Not Used U4, 0110/5 R53
Q60 "AB" Value 4K U4, 0101/6 R54


This table lists all the MCR-106 SCRs on the Lamp Driver module, the name of the lamp it drives,
the MC14514 decoder IC associated with the SCR along with the input signals (AD0, AD1, AD2, AD3) and output pin,
the CD4050 driver IC associated with the SCR along with the input and output pins,
and the name of the 2K Ohm resistor (red/black/red) connected to the decoder output.

MCR-106
SCR
Lamp MC14514
Decoder
CD4050
Driver*
2K Ohm
Resistor
Q1 Not Used U1, 1000/18 U5, 14/15 R6
Q2 Not Used U1, 1001/17 U5, 11/12 R5
Q3 Shoot Again U1, 1010/20 U5, 9/10 R4
Q8 Not Used U1, 0011/8 U5, 3/2 R16
Q9 Not Used U1, 0100/7 U5, 5/4 R17
Q10 "AB" Value 1K U1, 0101/6 U5, 7/6 R18
Q15 High Game To Date U2, 1100/14 U6, 14/15 R19
Q16 Ball In Play U1, 1100/14 U6, 11/12 R20
Q17 5X Potential U2, 1001/17 U6, 9/10 R21
Q22 "AB" Value 2K U2, 0101/6 U6, 3/2 R31
Q23 Match U2, 1010/20 U6, 5/4 R32
Q24 Not Used U2, 1000/18 U6, 7/6 R33
    
MCR-106
SCR
Lamp MC14514
Decoder
CD4050
Driver*
2K Ohm
Resistor
Q33 Game Over U3, 1100/14 U7, 14/15 R34
Q34 Not Used U2, 0100/7 U7, 9/10 R35
Q35 Not Used U2, 0011/8 U7, 11/12 R36
Q40 Playfield Shoot Again U3, 1001/17 U7, 3/2 R46
Q41 3X Potential U3, 1001/17 U7, 7/6 R48
Q42 Right Bottom Pop Bumper U3, 1000/18 U7, 5/4 R47
Q47 Tilt U4, 1100/14 U8, 14/15 R49
Q48 Not Used U3, 0100/7 U8, 9/10 R51
Q49 "B" Rollovers (x2) U3, 0011/8 U8, 11/12 R52
Q54 "A" Rollovers (x2) U4, 0011/8 U8, 3/2 R58
Q55 Not Used U4, 0100/7 U8, 5/4 R59
Q56 Left Bottom Pop Bumper U4, 1000/18 U8, 7/6 R60

*NOTE*
The AS-2518-23 Lamp Driver Module does not use the CD4050 hex driver chips
so ignore that column if that's the style of lamp driver you have.


NOTES
I got all this information from the schematics and pretty much copied it verbatim.
If you notice any mistakes (I'm only human), please let me know and I'll fix it up.
If you need to know which solenoid driver transistor goes to which solenoid driver board connector, Click Here.
If you need to know which lamp SCR goes to which lamp driver board connector, Click Here.



[Steve's Page] [Pinball] [Bally] [Mata Hari] [Bally Solenoid/Lamp Drivers]



Created 5/17/03 - Last Modified 1/24/09 - Steve Kulpa Mail Icon Nolensville, TN
Remove the NO_S*P*A*M_ to reply

All content posted on this page, unless otherwise noted, is the exclusive property of Steve Kulpa
and may not be borrowed, copied, downloaded, reproduced, or pilfered in any way with out prior permission