Everything You Ever Wanted to Know About
Silver Ball Mania Solenoid and Lamp Assignments

The following table lists each driver transistor, the coil it drives,
the pre-driver IC associated with it along with the pin numbers of the base and collector (respectively),
and the decoder IC BINARY input signals (ABCD) and output pin number.

TIP-102
Transistor
Coil CA3081
Pre-Driver IC
74L154
Decoder*
Q1 Not Used U1, 16, 1 0001/2
Q2 Not Used U1, 3, 2 0000/1
Q3 Knocker U1, 6, 4 0101/6
Q4 Outhole Kicker U1, 8, 7 0110/7
Q5 Not Used U1, 13, 14 0010/3
Q6 Not Used U1, 11, 12 0011/4
Q7 Not Used U1, 10, 9 0100/5
Q8 Right Pop Bumper U3, 16, 1 0111/8
Q9 Left Slingshot U3, 3, 2 1010/11
Q10 Right Slingshot U3, 8, 7 1011/13
Q11 Kick & Down Coil U3, 6, 4 1101/15
Q12 Up Kicker Coil U3, 10, 9 1100/14
Q13 Left Pop Bumper U3, 11, 12 1000/9
Q14 Center Pop Bumper U3, 13, 14 1001/10
Q15 Flipper Enable Relay U4, 3, 2 n/a
Q16 Not Used U4, 8, 7 1110/16
Q17 Not Used U4, 10, 9 n/a
Q18 Not Used U4, 11, 12 n/a
Q19 Coin Lockout U4, 13, 14 n/a

*NOTE*
"n/a" Decoder info indicates these drivers get their signals as continuous
solenoids directly from the MPU at A4J4-5, 6, 7, and 8 and not the Decoder IC.


This table lists all the 2N5060 SCRs on the Lamp Driver module, the name of the lamp it drives,
the decoder IC associated with the SCR along with the BINARY input signals (AD0, AD1, AD2, AD3) and output pin,
and the name of the 2K Ohm resistor (red/black/red) connected to the decoder output.

2N5060
SCR
Lamp MC14514
Decoder
2K Ohm
Resistor
Q4 Center "N" Target U1, 0111/4 R7
Q5 "S" On Insert U1, 1101/13 R3
Q6 "E" On Insert U1, 1110/16 R2
Q7 2nd "L" On Insert U1, 1011/19 R1
Q11 Upper "L" Side Target U1, 0110/5 R8
Q12 "E" Center U1, 0001/9 R12
Q13 2nd "L" Center U1, 0010/10 R13
Q14 "S" Center U1, 0000/11 R14
Q18 "I" On Insert U2, 1101/13 R15
Q19 "R" On Insert U2, 1110/16 R11
Q20 "A" Right Out Rollover U3, 0111/4 R10
Q21 3rd "L" On Insert U2, 1011/19 R9
Q25 Right "I" Return Rollover U2, 0111/4 R22
Q26 Lower "L" Side Target U2, 0110/5 R23
Q27 "R" Center U2, 0001/9 R27
Q28 3rd "L" Center U2, 0010/10 R28
Q29 "I" Center U2, 0000/11 R29
Q30 1st "L" On Insert U3, 1101/13 R30
    
2N5060
SCR
Lamp MC14514
Decoder
2K Ohm
Resistor
Q31 "B" On Insert U3, 1110/16 R26
Q32 "M" Left Out Rollover U3, 0110/5 R25
Q36 1st "L" Center U3, 0000/11 R45
Q37 Left "B" Target U3, 0101/6 R38
Q38 "B" Center U3, 0001/9 R41
Q39 Extra Ball Arrow U3, 1011/9 R24
Q43 "V" On Insert U4, 1101/13 R44
Q44 "M" Center U3, 0010/10 R43
Q45 "A" On Insert U4, 1110/16 R42
Q46 Kicker Special When Lit U4, 1001/17 R40
Q50 "A" Center U4, 0001/9 R55
Q51 MANIA Center U4, 0010/10 R56
Q52 Credit Indicator U4, 1010/20 R37
Q53 Left Spinner U4, 1011/19 R39
Q57 "V" Center U4, 0000/11 R57
Q58 Right Spinner U4, 0111/4 R50
Q59 "A" Left Return Rollover U4, 0110/5 R53
Q60 Top "A" Target U4, 0101/6 R54


This table lists all the MCR-106 SCRs on the Lamp Driver module, the name of the lamp it drives,
the MC14514 decoder IC associated with the SCR along with the BINARY input signals (AD0, AD1, AD2, AD3) and output pin,
the CD4050 driver IC associated with the SCR along with the input and output pins,
and the name of the 2K Ohm resistor (red/black/red) connected to the decoder output.

MCR-106
SCR
Lamp MC14514
Decoder
CD4050
Driver*
2K Ohm
Resistor
Q1 Top Center Rollover Lane U1, 1000/18 U5, 14/15 R6
Q2 2X Bonus U1, 1001/17 U5, 11/12 R5
Q3 5X Bonus and Shoot Again U1, 1010/20 U5, 9/10 R4
Q8 "N" Center U1, 0011/8 U5, 3/2 R16
Q9 Top "S" Target U1, 0100/7 U5, 5/4 R17
Q10 Left "E" Target U1, 0101/6 U5, 7/6 R18
Q15 High Score To Date U2, 1100/14 U6, 14/15 R19
Q16 Ball In Play U1, 1100/14 U6, 11/12 R20
Q17 3X Bonus U2, 1001/17 U6, 9/10 R21
Q22 Left "R" Target U2, 0101/6 U6, 3/2 R31
Q23 Match U2, 1010/20 U6, 5/4 R32
Q24 Bottom Kicker Up (2) U2, 1000/18 U6, 7/6 R33
    
MCR-106
SCR
Lamp MC14514
Decoder
CD4050
Driver*
2K Ohm
Resistor
Q33 Game Over U3, 1100/14 U7, 14/15 R34
Q34 Top "I" Target U2, 0100/7 U7, 9/10 R35
Q35 MANIA Center U2, 0011/8 U7, 11/12 R36
Q40 Same Player Shoots Again U3, 1001/17 U7, 3/2 R46
Q41 4K Bonus U3, 1001/17 U7, 7/6 R48
Q42 30K Bonus U3, 1000/18 U7, 5/4 R47
Q47 Tilt U4, 1100/14 U8, 14/15 R49
Q48 Top "L" Center U3, 0100/7 U8, 9/10 R51
Q49 MANIA Center U3, 0011/8 U8, 11/12 R52
Q54 Top Left & Right Rollover Lane U4, 0011/8 U8, 3/2 R58
Q55 Top "V" Target U4, 0100/7 U8, 5/4 R59
Q56 30K & Silverball Special U4, 1000/18 U8, 7/6 R60

*NOTE*
The AS-2518-23 Lamp Driver Module does not use the CD4050 hex driver chips
so ignore that column if that's the style of lamp driver you have.


NOTES
I got all this information from the schematics and pretty much copied it verbatim, so I don't really know what "Bottom Kicker Up" means, and I assume if you own this machine, you do.

If you notice any mistakes (I'm only human), please let me know and I'll fix it up.

If you need to know which solenoid driver transistor goes to which solenoid driver board connector, Click Here.

If you need to know which lamp SCR goes to which lamp driver board connector, Click Here.



[Steve's Page] [Pinball] [Bally] [Bally Solenoid/Lamp Drivers]



Created 9/16/02 - Last Modified 5/14/03 - Steve Kulpa Mail Icon Nolensville, TN
Remove the NO_S*P*A*M_ to reply

All content posted on this page, unless otherwise noted, is the exclusive property of Steve Kulpa
and may not be borrowed, copied, downloaded, reproduced, or pilfered in any way with out prior permission