Everything You Ever Wanted to Know About
Paragon Solenoid and Lamp Assignments

The following table lists each driver transistor, the coil it drives,
the pre-driver IC associated with it along with the pin numbers of the base and collector (respectively),
and the decoder IC BINARY input signals (ABCD) and output pin number.

TIP-102
Transistor
Coil CA3081
Pre-Driver IC
74L154
Decoder*
Q1 Drop Target (In Line) U1, 16, 1 0001/2
Q2 Bottom Thumper Bumper U1, 3, 2 0000/1
Q3 Knocker U1, 6, 4 0101/6
Q4 Outhole Kicker U1, 8, 7 0110/7
Q5 Not Used U1, 13, 14 0010/3
Q6 Not Used U1, 11, 12 0011/4
Q7 Not Used U1, 10, 9 0100/5
Q8 Treasure Chamber Saucer U3, 16, 1 0111/8
Q9 Left Thumper Bumper U3, 3, 2 1010/11
Q10 Right Thumper Bumper U3, 8, 7 1011/13
Q11 Left Slingshot U3, 6, 4 1101/15
Q12 Center Thumper Bumper U3, 10, 9 1100/14
Q13 Golden Cliffs Saucer U3, 11, 12 1000/9
Q14 Paragon Saucer U3, 13, 14 1001/10
Q15 Flipper Enable Relay U4, 3, 2 n/a
Q16 Right Slingshot U4, 8, 7 1110/16
Q17 3 Drop Target U4, 10, 9 n/a
Q18 Not Used U4, 11, 12 n/a
Q19 Coin Lockout U4, 13, 14 n/a

*NOTE*
"n/a" Decoder info indicates these drivers get their signals as continuous
solenoids directly from the MPU at A4J4-5, 6, 7, and 8 and not the Decoder IC.


This table lists all the 2N5060 SCRs on the Lamp Driver module, the name of the lamp it drives,
the decoder IC associated with the SCR along with the BINARY input signals (AD0, AD1, AD2, AD3) and output pin,
and the name of the 2K Ohm resistor (red/black/red) connected to the decoder output.

2N5060
SCR
Lamp MC14514
Decoder
2K Ohm
Resistor
Q4 Saucer "G" U1, 0111/4 R7
Q5 Spinner (1) Bottom U1, 1101/13 R3
Q6 10K Water Lane U1, 1110/16 R2
Q7 2X Golden Cliff U1, 1011/19 R1
Q11 Saucer "P" U1, 0110/5 R8
Q12 5K Bonus U1, 0001/9 R12
Q13 9K Bonus U1, 0010/10 R13
Q14 1K Bonus U1, 0000/11 R14
Q18 Spinner (2) U2, 1101/13 R15
Q19 5K Waterlane U2, 1110/16 R11
Q20 Saucer "N" U3, 0111/4 R10
Q21 4K Golden Cliff U2, 1011/19 R9
Q25 Saucer "O" U2, 0111/4 R22
Q26 Saucer "A" (Left) U2, 0110/5 R23
Q27 6K Bonus U2, 0001/9 R27
Q28 10K Bonus U2, 0010/10 R28
Q29 2K Bonus U2, 0000/11 R29
Q30 Spinner (3) U3, 1101/13 R30
    
2N5060
SCR
Lamp MC14514
Decoder
2K Ohm
Resistor
Q31 Player Up 3 U3, 1110/16 R26
Q32 Saucer "R" U3, 0110/5 R25
Q36 3K Bonus U3, 0000/11 R45
Q37 5X Bonus U3, 0101/6 R38
Q38 7K Bonus U3, 0001/9 R41
Q39 6K Golden Cliff U3, 1011/9 R24
Q43 Spinner (4) (Top) U4, 1101/13 R44
Q44 20K Super Bonus U3, 0010/10 R43
Q45 20K Golden Cliff U4, 1110/16 R42
Q46 Special Drop Target U4, 1001/17 R40
Q50 8K Bonus U4, 0001/9 R55
Q51 30K Super Bonus U4, 0010/10 R56
Q52 Credit Indicator U4, 1010/20 R37
Q53 8K Golden Cliff U4, 1011/19 R39
Q57 4K Bonus U4, 0000/11 R57
Q58 Special Treasure Saucer U4, 0111/4 R50
Q59 Saucer "A" (Right) U4, 0110/5 R53
Q60 Extra Ball Treasure Saucer U4, 0101/6 R54


This table lists all the MCR-106 SCRs on the Lamp Driver module, the name of the lamp it drives,
the MC14514 decoder IC associated with the SCR along with the BINARY input signals (AD0, AD1, AD2, AD3) and output pin,
the CD4050 driver IC associated with the SCR along with the input and output pins,
and the name of the 2K Ohm resistor (red/black/red) connected to the decoder output.

MCR-106
SCR
Lamp MC14514
Decoder
CD4050
Driver*
2K Ohm
Resistor
Q1 Center "P" U1, 1000/18 U5, 14/15 R6
Q2 Center "G" U1, 1001/17 U5, 11/12 R5
Q3 Shoot Again U1, 1010/20 U5, 9/10 R4
Q8 40K Super Bonus U1, 0011/8 U5, 3/2 R16
Q9 25K Drop Target U1, 0100/7 U5, 5/4 R17
Q10 2X Bonus U1, 0101/6 U5, 7/6 R18
Q15 High Score To Date U2, 1100/14 U6, 14/15 R19
Q16 Ball In Play U1, 1100/14 U6, 11/12 R20
Q17 Center "O" U2, 1001/17 U6, 9/10 R21
Q22 3X Bonus U2, 0101/6 U6, 3/2 R31
Q23 Match U2, 1010/20 U6, 5/4 R32
Q24 Center "A" (Left) U2, 1000/18 U6, 7/6 R33
    
MCR-106
SCR
Lamp MC14514
Decoder
CD4050
Driver*
2K Ohm
Resistor
Q33 Game Over U3, 1100/14 U7, 14/15 R34
Q34 Waterlane Special U2, 0100/7 U7, 9/10 R35
Q35 10K Drop Target U2, 0011/8 U7, 11/12 R36
Q40 Same Player S.A. U3, 1001/17 U7, 3/2 R46
Q41 Center "N" U3, 1001/17 U7, 7/6 R48
Q42 Center "R" U3, 1000/18 U7, 5/4 R47
Q47 Tilt U4, 1100/14 U8, 14/15 R49
Q48 Paragon Saucer Special U3, 0100/7 U8, 9/10 R51
Q49 15K Drop Target U3, 0011/8 U8, 11/12 R52
Q54 20K Drop Target U4, 0011/8 U8, 3/2 R58
Q55 5X Treasure Saucer U4, 0100/7 U8, 5/4 R59
Q56 Center "A" Right U4, 1000/18 U8, 7/6 R60

*NOTE*
The AS-2518-23 Lamp Driver Module does not use the CD4050 hex driver chips
so ignore that column if that's the style of lamp driver you have.


NOTES
I got all this information from the schematics and pretty much copied it verbatim.

If you notice any mistakes (I'm only human), please let me know and I'll fix it up.

If you need to know which solenoid driver transistor goes to which solenoid driver board connector, Click Here.

If you need to know which lamp SCR goes to which lamp driver board connector, Click Here.



[Steve's Page] [Pinball] [Bally] [Bally Solenoid/Lamp Drivers]



Created 5/3/08 - Last Modified 1/24/09 - Steve Kulpa Mail Icon Nolensville, TN
Remove the NO_S*P*A*M_ to reply

All content posted on this page, unless otherwise noted, is the exclusive property of Steve Kulpa
and may not be borrowed, copied, downloaded, reproduced, or pilfered in any way with out prior permission