Everything You Ever Wanted to Know About
Black Jack Solenoid and Lamp Assignments

The following table lists each driver transistor, the coil it drives,
the pre-driver IC associated with it along with the pin numbers of the base and collector (respectively),
and the decoder IC BINARY input signals (ABCD) and output pin number.

TIP-102
Transistor
Coil CA3081
Pre-Driver IC
74L154
Decoder*
Q1 10 Chime U1, 16, 1 0001/2
Q2 Not Used U1, 3, 2 0000/1
Q3 Knocker U1, 6, 4 0101/6
Q4 Out Hole Kicker U1, 8, 7 0110/7
Q5 100 Chime U1, 13, 14 0010/3
Q6 1000 Chime U1, 11, 12 0011/4
Q7 Extra Chime U1, 10, 9 0100/5
Q8 Saucer U3, 16, 1 0111/8
Q9 Center Pop Bumper U3, 3, 2 1010/11
Q10 Left Sling Shot U3, 8, 7 1011/13
Q11 Not Used U3, 6, 4 1101/15
Q12 Right Sling Shot U3, 10, 9 1100/14
Q13 Left Pop Bumper U3, 11, 12 1000/9
Q14 Right Pop Bumper U3, 13, 14 1001/10
Q15 Flipper Enable Relay U4, 3, 2 n/a
Q16 Not Used U4, 8, 7 1110/16
Q17 Not Used U4, 10, 9 n/a
Q18 Not Used U4, 11, 12 n/a
Q19 Coin Lockout U4, 13, 14 n/a

*NOTE*
"n/a" Decoder info indicates these drivers get their signals as continuous
solenoids directly from the MPU at A4J4-5, 6, 7, and 8 and not the Decoder IC.


This table lists all the 2N5060 SCRs on the Lamp Driver module, the name of the lamp it drives,
the decoder IC associated with the SCR along with the BINARY input signals (AD0, AD1, AD2, AD3) and output pin,
and the name of the 2K Ohm resistor (red/black/red) connected to the decoder output.

2N5060
SCR
Lamp MC14514
Decoder
2K Ohm
Resistor
Q4 1K Bonus U1, 0111/4 R7
Q5 Top Heart U1, 1101/13 R3
Q6 1st Player Up U1, 1110/16 R2
Q7 Saucer X-Ball U1, 1011/19 R1
Q11 17 Player U1, 0110/5 R8
Q12 17 Dealer U1, 0001/9 R12
Q13 "1" Spinner U1, 0010/10 R13
Q14 21 Dealer U1, 0000/11 R14
Q18 Top Spade U2, 1101/13 R15
Q19 2nd Player Up U2, 1110/16 R11
Q20 3K Bonus U3, 0111/4 R10
Q21 Saucer Special U2, 1011/19 R9
Q25 2K BONUS U2, 0111/4 R22
Q26 Right Out Lane U2, 0110/5 R23
Q27 Spade Bumper U2, 0001/9 R27
Q28 "2" Spinner U2, 0010/10 R28
Q29 20 Dealer U2, 0000/11 R29
Q30 Top Diamond U3, 1101/13 R30
    
2N5060
SCR
Lamp MC14514
Decoder
2K Ohm
Resistor
Q31 3rd Player Up U3, 1110/16 R26
Q32 Left Out Lane U3, 0110/5 R25
Q36 19 Dealer U3, 0000/11 R45
Q37 19 Player U3, 0101/6 R38
Q38 Diamond & Heart Spinner U3, 0001/9 R41
Q39 Saucer 2X U3, 1011/9 R24
Q43 Top Club U4, 1101/13 R44
Q44 "3" Spinner U3, 0010/10 R43
Q45 4th Player Up U4, 1110/16 R42
Q46 Player Wins U4, 1001/17 R40
Q50 Club Bumper U4, 0001/9 R55
Q51 "4" Spinner U4, 0010/10 R56
Q52 Credit Indicator U4, 1010/20 R37
Q53 5X U4, 1011/19 R39
Q57 18 Dealer U4, 0000/11 R57
Q58 4K Bonus U4, 0111/4 R50
Q59 Spinner 1000 U4, 0110/5 R53
Q60 18 Player U4, 0101/6 R54


This table lists all the MCR-106 SCRs on the Lamp Driver module, the name of the lamp it drives,
the MC14514 decoder IC associated with the SCR along with the BINARY input signals (AD0, AD1, AD2, AD3) and output pin,
the CD4050 driver IC associated with the SCR along with the input and output pins,
and the name of the 2K Ohm resistor (red/black/red) connected to the decoder output.

MCR-106
SCR
Lamp MC14514
Decoder
CD4050
Driver*
2K Ohm
Resistor
Q1 5K Bonus U1, 1000/18 U5, 14/15 R6
Q2 9K Bonus U1, 1001/17 U5, 11/12 R5
Q3 Shoot Again U1, 1010/20 U5, 9/10 R4
Q8 "5" Spinner U1, 0011/8 U5, 3/2 R16
Q9 "9" Spinner U1, 0100/7 U5, 5/4 R17
Q10 21 Player U1, 0101/6 U5, 7/6 R18
Q15 High Score To Date U2, 1100/14 U6, 14/15 R19
Q16 Ball In Play U1, 1100/14 U6, 11/12 R20
Q17 10K Bonus U2, 1001/17 U6, 9/10 R21
Q22 20 Player U2, 0101/6 U6, 3/2 R31
Q23 Match U2, 1010/20 U6, 5/4 R32
Q24 6K Bonus U2, 1000/18 U6, 7/6 R33
    
MCR-106
SCR
Lamp MC14514
Decoder
CD4050
Driver*
2K Ohm
Resistor
Q33 Game Over U3, 1100/14 U7, 14/15 R34
Q34 "10" Spinner U2, 0100/7 U7, 9/10 R35
Q35 "6" Spinner U2, 0011/8 U7, 11/12 R36
Q40 SPSA Playfield U3, 1001/17 U7, 3/2 R46
Q41 20K Bonus U3, 1001/17 U7, 7/6 R48
Q42 7K Bonus U3, 1000/18 U7, 5/4 R47
Q47 Tilt U4, 1100/14 U8, 14/15 R49
Q48 3X & Saucer 5X U3, 0100/7 U8, 9/10 R51
Q49 "7" Spinner U3, 0011/8 U8, 11/12 R52
Q54 "8" Spinner U4, 0011/8 U8, 3/2 R58
Q55 2X & Saucer 3X U4, 0100/7 U8, 5/4 R59
Q56 8K Bonus U4, 1000/18 U8, 7/6 R60

*NOTE*
The AS-2518-23 Lamp Driver Module does not use the CD4050 hex driver chips
so ignore that column if that's the style of lamp driver you have.


NOTES
I got all this information from the schematics and pretty much copied it verbatim.

If you notice any mistakes (I'm only human), please let me know and I'll fix it up.

If you need to know which solenoid driver transistor goes to which solenoid driver board connector, Click Here.

If you need to know which lamp SCR goes to which lamp driver board connector, Click Here.



[Steve's Page] [Pinball] [Bally] [Bally Solenoid/Lamp Drivers]



Created 6/30/03 - Last Modified 6/30/03 - Steve Kulpa Mail Icon Nolensville, TN
Remove the NO_S*P*A*M_ to reply

All content posted on this page, unless otherwise noted, is the exclusive property of Steve Kulpa
and may not be borrowed, copied, downloaded, reproduced, or pilfered in any way with out prior permission